New product

 1U rackmount, 7x Gigabit Ethernet, 1x Combo port (SFP or Gigabit Ethernet), 1xSFP+ cage, 9 cores x 1.2GHz CPU, 2GB RAM, LCD panel, Dual Power supplies, SmartCard slot, RouterOS L6 

More details

4 Items

In stock


Add to wishlist

Data sheet

Product codeCCR1009-7G-1S-1S+
Operating SystemRouterOS
License levelL6
CPU core count9
CPU nominal frequency1.2 GHz
Size of RAM2 GB
10/100 Ethernet portsNone
10/100/1000 Ethernet ports7
SFP ports1
SFP+ ports1
MiniPCI slotsNone
MiniPCI-e slotsNone
Number of chainsNone
Antenna gain DBINo
Number of USB ports1
USB slot typemicroUSB type AB
Serial portRS232 + Header
Operating temperature range-20C .. +60C
Power Jack2
Supported input voltage15 V - 57 V
Max Power consumption34W
802.3af supportNo
PoE inYes
PoE outNo
Voltage MonitorYes
Current MonitorYes
CPU temperature monitorYes
PCB temperature monitorYes

More info


The new updated revision of CCR1009 is here. We attempted to combine all the customer feedback and best practice in CCR device manufacturing that we learned over the last three years, since the first CCR1009 devices were launched.

Important changes

No switch-chip - the device now features only fully independent Ethernet ports each with a direct connection to the CPU, allowing to overcome previous shared 1Gbit limitation from switch-chip ports and utilize full potential of CPU processing power on those ports.

Combo-port - a single 1Gbit software interface that has two hardware interfaces - an SFP cage and a Gigabit Ethernet port, allowing you to use any type of connection available to you. It is also possible to switch between both physical interfaces in RouterOS. In an event of disconnect the combo-port provides hardware fail-over feature.

100Mbps SFP support - this is our first device that supports 100BASE-LX/100BASE-SX/100BASE-BX fiber modules, as well as standard 1.25G SFP modules.

More throughput - because the ports are now directly connected to the CPU, the new CCR1009 can achieve even higher throughput.

Ethernet test results

CCR1009-7G-1C-1S+Tile 9 core all port test with combo-port and SFP+
ModeConfiguration1518 byte512 byte64 byte
Bridgingnone (fast path)1,300.415,792.13,759.415,398.517,782.89,104.8
Bridging25 bridge filter rules1,244.415,112.01,395.35,715.11,368.1700.5
Routingnone (fast path)1,300.415,792.13,759.415,398.517,411.28,914.5
Routing25 simple queues1,300.415,792.11,925.68,195.41,977.01,328.5
Routing25 ip filter rules739.28,976.8793.93,378.8801.8538.8
  1. All tests are done with Xena Networks specialized test equipment (XenaBay),and done according to RFC2544 (Xena2544)
  2. Max throughput is determined with 30+ second attempts with 0,1% packet loss tolerance in 64, 512, 1518 byte packet sizes
  3. Values in Italic indicate that max throughput was reached without maxing out CPU, but because board interface configuration was maxed out
  4. Test results show device maximum performance, and are reached using mentioned hardware and software configuration, different configurations most likely will result in lower results


Write a review



 1U rackmount, 7x Gigabit Ethernet, 1x Combo port (SFP or Gigabit Ethernet), 1xSFP+ cage, 9 cores x 1.2GHz CPU, 2GB RAM, LCD panel, Dual Power supplies, SmartCard slot, RouterOS L6